tel
  • +86-21-64911960
  • Call us for Consultation
greentel

+008613391393652

Mechanical Seal Cartex

  • Contact Us

  • Eu-Flo Pump Industries Co Ltd
  • Pump Expert of European Standard
  • Tel: 021-64911960
  • Phone: 13391393652
  • Email: [email protected]
  • Address:Room 1506, 638 Heng Feng Road, Su He No.1 Mansion,200040.Shanghai,China

Similar Products

  • Mechanical Seal CR/CDL

    Description:eps bb1 between bearing axially split casing pump

    More
  • Mechanical Seal MG1

    Description:eps bb1 between bearing axially split casing pump

    More
  • Shaft Seal M74

    Description:eps bb1 between bearing axially split casing pump

    More

Cartridge sealsare self-contained units consisting of a shaft sleeve, seal,and gland plate. The unit is fitted onto the pump shaft as a built assembly, and no further fitting is required.

Cartridge seals are an attempt to over-come the fitting problems of conventional seals.They are supplied in single and double form, and the gland plate is often fitted with various tappings to provide for flushing, cooling water injection, and disaster control. The cartridge can overcome several limitations of the standard pump gland. Tangential tappings for introducing fluids into the gland cause less disturbance to the sealface than the radial tappings often found on pump units. Look again at the tapping provided for flush water to the packed gland, a tangential tapping would provide a less turbulent water source. For a packing gland this may not be important but to a mechanicalsealit can be another adverse condition with which to cope.

The setting position of the seal is set by the cartridge design, but the seal unit should not be screwed to the shaft until the gland plate is secured to the pump and any adjustments made to the shaft position. Once this has been completed the set screws can be tightened and the spacers removed.

So, what can go wrong. The design works to eliminate many of the common causes of seal failure on installation and because the seal is presented on its own shaft sleeve any damage that might be caused by a conventional seal to the pump unit is also eliminated.

The problem is that the seal has to be very compact to fit into the available space. Seals require mass to produce as high a co-efficient of inertia as possible. The higher the mass the less affected the rotation parts are to transient vibrations. Such vibrations will be absorbed lessening the tendency to vibrate the sealfaces apart. Remember if the sealfaces open then they are immediately vulnerable to contamination from the myriad dirt particles swirling around your plant. When the seal faces close those particles are trapped, in a carbon ceramic combination the particles become embedded in the carbon and begin to score away at the mating face. I must make it clear that all seals fitted into gland boxes pre-owned by a packing gland are subject to these problems. All seals are a compromise on dimensions, they are no good if they do not fit! The specific problem of the cartridge seal is that the components further reduce the available space into which a large enough mass can be inserted to cope with vibrations.

If you are going to use this type of seal

then it is important that the unit you fit it to is in good condition. Bearings within tolerance, shaft unbent, impeller in balanced condition, system not experiencing the effects of cavitation.

You will pay a lot of money for a first class seal unit, so make sure you achieve all of the benefits by checking out the pump unit for defects.

Type Cartex.

External 2 bolt, balanced Cartridge Mechanical Seal,with dual tangential environmental controls. The cartex is an excellent Gland Packing replacement that will fit majority of equipment, and removes potential for fitting error.

Type Cartex.

External 4 bolt, balanced Cartridge Seal.A cost effective general Cartridge Mechanical Seal,featuring advanced design features and exceptional performance, whilst reducing fitting error and lowering maintenance costs.

Type cartex.

External 4 bolt, balanced Cartridge Mechanical Seal,with dual environmental controls. A cost effective general Cartridge Seal,exceptional design features and performance, whilst reducing fitting error and lowering maintenance costs.

Cartex  SE/SO   Single Seal

Cartex  DE      Double Seal

Operating Limits :

Pressurel: ≤2.1MPa

Speed: ≤25m/s

Temperature: -30˚C~+220˚C

 

Rotary Ring (SiC/Carbon/TC)

Stationary Ring (SiC/TC)

Secondary Seal (VlTON/Encapsulated Ring/PTFE)

Other Parts (SUS304/SUS316/Titanium/Hastelloy-C)

 

 

 

 

 

 

 

INQUIRY NOW